Плата распределения питания Matek HUBOSD8 eco

 Matek HUBOSD8 eco H-Type current Sensor  140A & Dual 5V/2A &12V/500mA BEC 

The HUBOSD8 has been engineered to provide the highest possible performance and reliability in a 46*36mm & 4 layers PCB. It is a multifunctional HUB with PDB, BEC 5V/2A &12V/500mA, Current sensor 140A, STOSD8. It is specially made for the mini FPV Quad. The BEC 12V is linear regulator, no LC Filter needed. Built-in STOSD8 can support Plug & Play, no complicated settings needed.

General

Input voltage range (3S-5S operation): 8 - 21VDC

PDB: 4x30A (Max.4x35A)

Regulated 5V and 12V outputs

Current Sensor 140A

Built-in STOSD8 Physical: - 2oz copper, 4-layers &1.6mm PCB.

- 1x Battery input, 4x ESC outputs. 2x BEC 5V outputs, 2x BEC 12V outputs. - Camera signal & Gnd pads, Video Transmitter Signal & Gnd pads

- 1x Serial port (RX, TX, G)

- Dimensions: 46x36x4mm, Weight: 8.5g

- Mounting holes 30.5mm square spacing

PDB (ESC outputs)

Continuous current: 30A per output

Peak current (10 seconds/minute): 35A per output

BEC 5V outputs

Designed for RC Receivers, Flight controllers, OSD, and Servos.

DC/DC synchronous buck regulator.

Voltage: 5.0 +/- 0.1VDC

Continuous current: 2 Amps (Max.2.5A 10s/minute)

Output Ripple: 40mV (VIn=16V, VOut=5V@2A load)

Short-circuit tolerant (5 seconds/minute)

BEC 12V outputs

Linear regulator, very low noise.

LC Filter is needless.

Designed for Video TX or FPV camera.

Voltage: 12.0 +/- 0.3VDC (4~5S operation)

Continuous current: 500mA@16V IN, 400mA@20V IN

Short-circuit tolerant (2 seconds/minute)

If the battery is 3S LiPo, Output voltage=3S LiPo voltage - 1V

Current Sensor

140A If current >140A.

STOSD display 140A

STOSD8

Running indicator

 Blue LED blinks: STOSD is initializing

Blue LED light: STOSD is working.

Autodetect PAL/NTSC

Auto sense PAL / NTSC cam at OSD startup. Default is NTSC without Cam signal Dynamic on screen info

Current < 2A & keep 5 seconds    Current > 2A

Min.Volt & Max.Amp recorder

Automatic flight timer

Current > 2A, Time in. Current < 2A,Time out..

Auto battery cells detection

If the Input voltage is in the range of following, The HUBOSD will detect the cell numbers automatically.

11.1~13.05V: 3cells LiPo, 14.8~17.4V: 4cells LiPo, 18.5~21V: 5cells LiPo If the input voltage is out of the range. The voltage value will blink on screen.

Pls check if the battery total voltage is below 3.7V*cells

Low vlotage alarm (Value blinks): Default 3.6V* cells

Exceeding mAh alarm (Value blinks): Default 1000mAh

Onscreen Pilot ID Default is disable. you can type some words & enable it in GUI

Firmware upgradable

Voltage precision: +/- 0.4%, Voltage resolution: 0.01V Current precision: +/- 1.5%, Current resolution: 0.1A